Tube Installation Tools
GSI proudly represents Elliott Tool Technologies in the Gulf region as the exclusive manufacture representative. This means a purchase from us comes directly from the factory and you pay factory-direct prices. In addition to the lowest possible prices, you receive the fastest lead-times possible and the most extensive inventory in the industry. When you go to install new tubes, whether it be chiller, condenser, heat exchanger or boiler tubes, remember GSI and Elliott Tool is here to support your most critical projects.
Tube Installation Tools: Tube Expanders
Explore our extensive range of tube installation tools for rolling or "expanding" tubes in to boiler drums, header boxes, heat exchanger tube sheets and chillers.
.png)
Condenser Tube Expanders
For Heat Exchanger Tube Rolling
Elliott’s 24 Series Condenser Expanders are ideal for expanding tubes in chillers, heat exchangers, feedwater heaters, fin fan coolers, and surface condensers.
Tube Size: 0.500" to 2.000" (12.7 - 50.8mm) OD
Roll Type: Straight
Application: Chiller, heat exchanger, feedwater heater, fin fan cooler, and surface condenser.
Click here for spec sheet
Flared Boiler Tube Expanders
For Boiler Tube Flare Rolling
Elliott’s 900 Series Flaring Boiler Expanders are self-feeding, specifically made for use in superheaters in watertube boilers or evaporator tubes. In only one operation, these expanders roll tubes parallel and flare projecting tube ends at 15 degrees from the tool center line.
Tube Size: 0.620” to 1.500” (15.4 – 38.1mm) OD
Roll Type: Flaring
Application: Superheaters, watertube boilers, and evaporator tubes.
Click here for spec sheet
Single Roll Beading Expadners
For Combo Rolling Boiler Tubes
Elliott’s 4480 Series Single Roll Beading Expanders expand the tube into the tube sheet while forming a bead at the end of the tube required in Firetube boiler applications.
Tube Size: 2.000” to 3.000” (50.8 – 76.2mm) OD
Roll Type: Roll Beading
Application: Firetube Boiler
Click here for spec sheet
Straight Roll Boiler Expanders
For Rolling Boiler Tubes
Elliott’s 40 Series Straight Boiler Expanders are recommended for re-rolling leaky tube joints in Firetube boilers. Self-feeding, these expanders should primarily be used by hand.
Tube Size: 2.000” to 3.000” (50.8 – 76.2mm) OD
Roll Type: Straight
Application: Firetube Boiler
Click here for spec sheet
Deep Roll Boiler Expanders
For Boiler Tube Rolling
Elliott’s DRE Series Deep Roll Boiler Expanders are used for deep and hard rolling of steam and mud drums found in high-pressure boilers.
Tube Size: 1.750” to 4.000” (44.5 – 101.6mm) OD
Roll Type: Straight
Application: Steam & Mud Drums and Watertube Boiler
Click here for spec sheets
Parallel Pin Expanders
For Assisted Tube Rolling Systems
Elliott's PX24 Series offer true parallel pin tube expansion, which can reduce the stress created on welded tube joints when compared to tapered rolling.
Tube Size: 0.750″ to 1.000″ (19.05 – 25.4mm) OD
Roll Type: Parallel Pin Condenser Expander
Application: Chillers, heat exchangers, feedwater heaters, fin fan coolers, and surface condensers.
Click here for spec sheets
Tube Installation Tools: Rolling Motors
Explore our extensive range of tube installation tools for rolling or "expanding" tubes in to boiler drums, header boxes, heat exchanger tube sheets and chillers.
Right Angle Pneumatic Roll Motors
For Rolling Boiler Tubes
The powerful 445 Series Motors are ideal for tough boiler tube applications. The right angle heads are suitable for rolling tubes in hard to reach, tight areas. Now available in torque controlled & stall type motors.
Tube Size: 2.000” to 4.000” (50.8 – 101.6mm) OD
Type: Right Angle Pneumatic Rolling Motor
Style: Torque Controlled or Stall Type
ET850 Torque Controlled Pneumatic Rolling Motor
For Rolling Boiler & Heat Exchanger Tubes
Elliott's ET850 Motor is the next evolution of push-pull motors. Offering the same USA quality and performance you're used to, with additional features to improve the operator's experience.
Tube Size: 0.750” to 1.250” (19.1 – 31.8mm) OD
Type: Rolling Motor
Power: Pneumatic
Torque: Torque Controlled
ET720 Torque Controlled Pneumatic Rolling Motor
For Rolling Heat Exchanger & Chiller Tubes
The ET Motors are ideal for rolling small tubes commonly found in oil coolers and other small heat exchangers. These motors have undergone extensive testing, proving long tool life and quality.
Tube Size: 0.250” to 0.375” (6.35 – 9.525mm) OD
Type: Rolling Motor
Power: Pneumatic
Torque: Torque Controlled
Stall Torque Pneumatic Rolling Motor
For Rolling Boiler Tubes
Elliott’s Stall Torque Pneumatic Rolling Motors are the most powerful motors available for rolling tubes in extreme applications. The motors are recommended for use in heavy wall, thick drum applications in watertube boilers.
Tube Size: 0.750” to 6.000” (19.1 – 152.4mm) OD
Type: Rolling Motor
Power: Pneumatic
Torque: Stall Torque
Electric Rolling Motors
For Rolling Boiler Tubes & Heat Exchanger Tubes
Elliott’s 99 Series electric rolling motors offer better consistency, faster RPMs, and comparable torque to that of pneumatic offerings.
Tube Size: 0.250” to 3.000” (6.4 – 76.2mm) OD
Type: Rolling Motor
Power: Electric 110V or 220V
Torque: Torque Controlled with ELC
Assisted Roll Systems
For Fast Rolling Heat Exchanger Tubes & Parallel Pin Rolling
Elliott offers 4 different assisted tube rolling systems: Table Hawk, Rapid Hawk Electric, Rapid Hawk Hybrid, and the Monster Hawk. Each system comes equipped with a variety of features to suit a specific industry application.
Tube Size: 0.25" to 3.00" (6.35 - 76.2mm) OD
ELC Torque Control Box
For Controlling Torque Output on Elliott Electric Roll Motors
Elliott’s ELC110220 is the first torque control with an Embedded Logic Controller that senses and is compatible with both 110V or 220V automatic, and manual reverse rolling motors.
Tube Size: 0.250" to 3.000" (6.4 - 76.2mm) OD
Voltage: 110V to 240V
Languages: English or Spanish
Compatibility: Elliott’s 99 Series Electric Rolling Motors (other electric motors with optional adapters)
Auto-Reverse
Tube Expander Lubricant
For Maximizing Tube Expander Tool Life Paste & Liquids Available
Elliott’s Lubricants are engineered to provide the best lubrication in tube rolling and roll beading applications. They will provide time and tool savings compared to commonly available lubricants.
Paste Lubricant
Liquid Lubricant
Bead Coolant
Cutting Oil
Contact
Contact us 24/7 for rentals, demos, training programs, expert support and emergency tool deliveries.
17351 Hard Hat Dr B14, Covington, LA 70433, USA